Chromium manganese titanium steel and boron steel

Aug 15, 2022

Leave a message

For a long time, the most commonly used steel grade for truck gears in my country is 20CrMnTi. This is a medium-sized automobile gear 18XTr steel (ie 20CrMnTi steel) introduced from the former Soviet Union in the 1950s. The steel has fine grains, small grain growth tendency during carburizing, good carburizing and quenching properties, and can be directly quenched after carburizing. The literature points out that before 1980, my country's carburized alloy structural steel (including 20CrbinTi steel) only guaranteed the chemical composition of the steel and the mechanical properties measured by the samples when the steel left the factory, but the chemical composition and mechanical properties often appeared in the production of automobiles. For qualified steel, the product quality is affected due to the large fluctuation range of hardenability. For example, if the hardenability of 20CrMnTi carburized steel is too low, the core hardness of the gear after carburizing and quenching will be lower than the value specified in the technical conditions, and the fatigue life of the gear will be reduced by half during the fatigue test; if the hardenability is too high If it is too high, the shrinkage of the inner hole after carburizing and quenching of the gear is too large, which will affect the gear assembly.

Since the hardenability of steel has an extremely significant impact on the hardness and distortion of the gear tooth core, in 1985, the Ministry of Metallurgy promulgated my country's technical conditions for guaranteed hardenability structural steel (GB5216-85), which is included in this technical condition. The chemical composition and hardenability data of 10 kinds of carburized steels including 20CxMnTiH and 20MnVBH steels were obtained. The standard stipulates that the hardenability index of 20CrMnTi steel used for manufacturing gears is 30-42HRC at a distance of 9 coffee from the water-cooled end. After that, the problems of too low hardness and too large distortion in the tooth center of gears produced by using 20CrMnTi steel were basically solved. However, it is obviously unreasonable to use the same steel grade 20CrMnTi regardless of the size of the gear module and the thickness of the steel section. Due to the improvement of steel smelting technology in my country and the improvement of the supply of alloy structural steel, it has been possible to further narrow the hardenability band of gear steel and develop it according to the requirements of different products (such as transmission gears and rear axle gears, etc.). New steel grades to meet its requirements.

Through negotiation with steel mills, in 1997, Changchun FAW successively signed an agreement with the manufacturers of gear steel mills to supply the hardenability of 20CrMnTi steel in batches. The hardenability groups of 20CrMnTiH steel used for the first shaft, intermediate shaft gear of the small transmission and the main and driven bevel gears of the rear axle with larger cross-sectional dimensions are I and II, respectively, and the corresponding hardenability are J9: 30-36HRC and J9=36~42HRC.

Around 1960, due to the tight supply of nickel and chromium steel in China, the production of nickel and chromium steel in my country was affected. At that time, my country's automobile industry was a technology imported from the former Soviet Union, and the Soviet Union used a large number of steels containing nickel and chromium. Therefore, at that time, my country's automobile industry vigorously developed the development and research of boron steel, and used 20MnVB and 20Mn2TiB steel to replace 20CrMnTi carburized steel to manufacture gears. This is because adding a trace amount of boron (0.0001%-0.0035%) to the structural steel can significantly improve the hardenability of the steel, so adding a trace amount of boron to the steel can replace a certain amount of precious alloying elements such as manganese, nickel, chromium, molybdenum, etc. Therefore, boron steel is widely used. Changchun FAW has used 20MnTiB and 20Mn2TiB steels in the production of "Jiefang" brand automobile gears.

The "Dongfeng" brand 5 produced by Dongfeng Motor Corporation is made of 20CrMnTi and 20MnVB steel for the transmission and rear axle gear of the truck. Likewise, an agreement was signed with the steel mill to narrow the hardenability band of the steel and supply it in batches. The steels used for the main and driven bevel gears of the transmission and rear axle are 20CrMnTiH(3), 20MnVBH(2), and 20MnVBH(3), respectively, and the corresponding hardenability is J9=32~39HRC and J9=37~44HRC, J9=34 ~42HRC.

my country's Qijiang Gear Factory introduced the German company's heavy-duty vehicle transmission gear production technology, and successfully trial-produced the company's Cr-Mn-B series boron-containing gear steel in accordance with the German company's standards. The hardenability of the gear material is J10=31~39HRC

spur gear

Of course, 20CrMnTi steel, 20MnTiB steel, 20MVB steel and other boron-containing steels also have deficiencies. It is generally believed that 20CrMnTi and other carburized steels are essentially fine-grained steels, and the grains will not be coarsened after carburizing, and can be directly quenched. But in fact, due to the influence of steel smelting quality, grain coarsening often occurs under normal conditions. The actual grain size test of several batches of materials found that a considerable part of the actual grain size was only 2-3 grades (under the condition of 930 ℃ heat preservation for 3h). The literature believes that due to the high content of Ti, 20CrMnTi has many TiN inclusions in the steel, especially the large TiN inclusions are the fatigue source of gear fatigue, and its existence will reduce the contact fatigue performance of gears. The inclusions have a cubic structure and are prone to cleavage and cracking when subjected to force, resulting in early failure of the gear. Another problem is that the hardenability of this steel is limited, and it cannot meet the requirements of large-diameter and large-modulus gears. The depth of the effective hardened layer of carburizing and the hardness of the core cannot meet the requirements of heavy-duty gears. In addition, 20CrMnTi steel is prone to internal oxidation and non-martensitic structure during heat treatment, which reduces the fatigue life of gears. But in our country gear carburizing steel, there is no kind of steel as mature and reliable as 20CrMnTi steel in carburizing process. Therefore, it is still the most commonly used carburizing steel in China. Boron steels such as 20MnVB, 20MnTiB and 20Mn2TiB also have some shortcomings. For example, due to poor deoxidation and denitrification during smelting, boron cannot play a role in increasing the hardenability. Therefore, the performance of boron steel is unstable. The gear distortion increases and affects the quality of the product. At the same time, because the mixed grains and grains are easy to be coarse, the deformation is not easy to control and the toughness is poor, and the root of the boron steel gear is prone to produce trosteite structure and black mesh and black belt of the carbonitriding gear. Therefore, many factories discontinued the use of this steel. However, it must not be concluded that boron steel is not suitable for gear carburizing steel. Carburized steel containing boron is also used abroad. For example, the famous IV gear factory in Germany has been using the reserved steel grade ZF7 formulated by its own factory, which is a low-carbon chromium-manganese steel containing boron. The main chemical components (mass fraction, %) of the steel are 0.15-0.20C, 0.15-0.40S, 1.0-1.3Cr, 1.0-1.3Mn, 0.001-0.003B. Some American automobile transmission gears and rear axle main and driven gears also use boron-containing carburized steel, such as 50B15, 43BVl4 and 94B17. Therefore, as long as the smelting technology of steel mills keeps up, the above problems of boron steel can be solved.

The processing of 20CrMnTiH, 20MnVBH and 20MnTiBH steel gear forging billets in a continuous isothermal normalizing furnace can ensure a uniform distribution of flake pearlite + ferrite. In this way, the heat treatment distortion of the gear can be greatly reduced, the precision of the gear can be improved, and the service life of the gear can be prolonged.

The isothermal normalizing hardness of gear forging blank is 156~207HB


Send Inquiry